- 您现在的位置：买卖IC网 > Sheet目录395 > AT86RF231-ZFR (Atmel)TXRX LOW POWER 2.4GHZ 32VQFN
AT86RF231
8.2.3
8.2.4
Automatic FCS generation
The automatic FCS generation is performed with register bit TX_AUTO_CRC_ON = 1 (reset
value). This allows the AT86RF231 to compute the FCS autonomously. For a frame with a frame
length specified as N (3 ≤ N ≤ 127), the FCS is calculated on the first N-2 octets in the Frame
Buffer, and the resulting FCS field is transmitted in place of the last two octets from the Frame
Buffer.
If the radio transceivers automatic FCS generation is enabled, the Frame Buffer write access
can be stopped right after MAC payload. There is no need to write FCS dummy bytes.
In RX_AACK mode, when a received frame needs to be acknowledged, the FCS of the ACK
frame is always automatically generated by the AT86RF231, independent of the
TX_AUTO_CRC_ON setting.
Example:
A frame transmission of length five with TX_AUTO_CRC_ON set, is started with a Frame Buffer
write access of five bytes (the last two bytes can be omitted). The first three bytes are used for
FCS generation; the last two bytes are replaced by the internally calculated FCS.
Automatic FCS check
An automatic FCS check is applied on each received frame with a frame length N
2. Register
bit RX_CRC_VALID (register 0x06, PHY_RSSI) is set if the FCS of a received frame is valid.
The register bit is updated when issuing interrupt IRQ_3 (TRX_END) and remains valid until the
next TRX_END interrupt caused by a new frame reception.
In RX_AACK mode, if FCS of the received frame is not valid, the radio transceiver rejects the
frame and the TRX_END interrupt is not issued.
In TX_ARET mode, the FCS and the sequence number of an ACK is automatically checked. If
one of these is not correct, the ACK is not accepted.
86
8111C–MCU Wireless–09/09
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AT86RF232-ZX
2.4 GHZ ZIGBEE TRANSCEIVER
AT88CK201BK
BRD CRYPTORF READER AT88RF1354
AT88SC-ADK2
KIT ARIS+ DK CRYPTOMEM/COMPANION
AT88SC3216CRF-MY1
IC EEPROM 32KBIT 13MHZ TAG
ATA-2001
LVDT AMPLIFIER
ATAB5429-9-B
BOARD BASESTATN UHF RCVR 915MHZ
ATAB5749-3
BOARD XMITTER FOR 315MHZ ATA5749
ATAKSTK511-3
KIT RF MODULE 315MHZ FOR STK500
相关代理商/技术参数
AT86RF231-ZU
功能描述:射频收发器 2.4GHz Zigbee Transceiver
RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF231-ZU_09
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Low Power 2.4 GHz Transceiver for ZigBee
AT86RF231-ZUR
功能描述:射频收发器 2.4GHz, Zigbee Transceiver
RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF232-ZX
功能描述:射频收发器 2.4 GHZ ZIGBEE TRANSCEIVER
RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF232-ZXR
功能描述:射频收发器 2.4 GHZ ZIGBEE TRANSCEIVER
RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF233-ZF
功能描述:IC RF TXRX+MCU 802.15.4 32-VFQFN 制造商:microchip technology 系列:- 包装:托盘 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4，通用 ISM > 1GHz 协议:6LoWPAN，Zigbee? 调制:O-QPSK 频率:2.4GHz 数据速率（最大值）:2Mbps 功率 - 输出:4dBm 灵敏度:-101dBm 存储容量:128B SRAM 串行接口:SPI 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:11.3mA ~ 11.8mA 电流 - 传输:7.2mA ~ 13.8mA 工作温度:-40°C ~ 125°C 封装/外壳:32-VFQFN 裸露焊盘 标准包装:490
AT86RF233-ZFR
功能描述:IC RF TXRX+MCU 802.15.4 32-VFQFN 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4，通用 ISM > 1GHz 协议:6LoWPAN，Zigbee? 调制:O-QPSK 频率:2.4GHz 数据速率（最大值）:2Mbps 功率 - 输出:4dBm 灵敏度:-101dBm 存储容量:128B SRAM 串行接口:SPI 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:11.3mA ~ 11.8mA 电流 - 传输:7.2mA ~ 13.8mA 工作温度:-40°C ~ 125°C 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1
AT86RF233-ZU
功能描述:射频收发器 2.4GHz ZigBee Transceiver
RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray